+++ /dev/null
-#!/bin/bash
-
-# parameters
-#
-# ============================================================================
-#
-# Copyright (C) THALES. All rights reserved
-# Author: Laurent Mazet
-#
-# 2013-11-10 V1.0 : Creation
-#
-# 2013-11-20 V1.1 : L.Mazet ajout possibilite de configuration du switch
-#
-# ============================================================================
-
-DRY=
-ID=
-IP=192.168.0.1
-#TRC6500_SCRIPT_DIR=/opt/trc6500/script
-TRC6500_SCRIPT_DIR=$(dirname $0)
-
-# help function
-
-function usage () {
- echo "usage: $PROGNAME [-a] [-d] [-h] [-i <id>]"
- echo " -a: configure all boards"
- echo " -d: dry mode"
- echo " -h: help message"
- echo " -i: board id (from 1 to 5)"
- exit $@
- }
-
-# formating functions
-
-function title () { echo -e "\033[0;1m$*\033[0;0m"; }
-function pass () { echo -e "\033[1;32m$*\033[0;0m"; }
-function warn () { echo -e "\033[1;33m$*\033[0;0m"; }
-function fail () { echo -e "\033[1;31m$*\033[0;0m"; }
-
-# configuration values
-
-# argument processing
-
-while [ $# -gt 0 ]; do
- case "$1" in
- -a) ID=all;;
- -d) DRY=yes;;
- -h) usage 0;;
- -i) shift; ID=$1;;
- *) usage 1;;
- esac
- shift
-done
-
-# switch port configure function ()
-
-function sw_configure () {
- case "$1" in
- off) CMD="-c 'configure terminal' -c 'interface range g1/39-44' -c 'shutdown' -c end -c 'clear mac address-table dynamic' -c 'clear ip arp inspection log' -c exit";;
- on) CMD="-c 'configure terminal' -c 'interface range g1/39-44' -c 'no shutdown' -c end -c exit";;
- 1) CMD="-c 'configure terminal' -c 'interface g1/39' -c 'no shutdown' -c end -c exit";;
- 2) CMD="-c 'configure terminal' -c 'interface g1/40' -c 'no shutdown' -c end -c exit";;
- 3) CMD="-c 'configure terminal' -c 'interface g1/41' -c 'no shutdown' -c end -c exit";;
- 4) CMD="-c 'configure terminal' -c 'interface g1/42' -c 'no shutdown' -c end -c exit";;
- 5) CMD="-c 'configure terminal' -c 'interface g1/43' -c 'no shutdown' -c end -c exit";;
- 6) CMD="-c 'configure terminal' -c 'interface g1/44' -c 'no shutdown' -c end -c exit";;
- esac
-
- if [ "$DRY" = "yes" ]; then
- echo connect_switch.tcl -h swm $CMD
- else
- LOG=/tmp/$PROGNAME-$$.log
- echo -n "sw_configure $1: "
- eval $TRC6500_SCRIPT_DIR/connect_switch.tcl $CMD swm >&$LOG && pass OK || { fail KO; cat $LOG; exit 1; }
- rm -f $LOG
- fi
-}
-
-case "$ID" in
-1) CH1=0; CH2=1; CLOCKREF=external;;
-2) CH1=2; CH2=3; CLOCKREF=internal;;
-3) CH1=4; CH2=5; CLOCKREF=internal;;
-4) CH1=6; CH2=7; CLOCKREF=internal;;
-5) CH1=8; CH2=9; CLOCKREF=internal;;
-6) CH1=10; CH2=11; CLOCKREF=internal;;
-all)
- for id in $(seq 1 5); do
- title "switch off all fe306 ports"
- sw_configure off
- title "switch on port for fe306 $id"
- sw_configure $id
- title "configure fe306 $id"
- if [ "$DRY" = "yes" ]; then
- echo $(basename $0) -i $id
- else
- { $0 -i $id | mawk -W interactive '{print " " $0}'; } && pass OK || { fail KO; exit 1; }
- fi
- done
- title "switch on all fe306 ports"
- sw_configure on
- exit 0
- ;;
-*) echo "unknown fe306 id ($ID)"; exit 1;;
-esac
-
-# configure function
-
-function configure () {
- echo -n "$1 [$2 <= $3]: "
- if [ "$DRY" = "yes" ]; then
- echo wget -q -O - http://$IP/$1?$2=$3
- else
- wget -q -O - http://$IP/$1?$2=$3 >/dev/null && pass OK || { fail KO; exit 1; }
- fi
-}
-
-# setup local address
-
-title "setup local address"
-cmd="ifconfig eth1:1 192.168.0.2 netmask 255.255.255.0"
-[ "$DRY" = "yes" ] && echo $cmd || { echo -n $cmd" "; eval $cmd && pass OK || { fail KO; exit 1; }; }
-
-# check if fe306 is connected
-
-#title "check presence of $IP"
-#cmd="ping -c 1 -w 10 -W 10 $IP"
-#[ "$DRY" = "yes" ] && echo $cmd || { echo -n $cmd" "; eval $cmd >&/dev/null && pass OK || { warn KO; ifconfig eth1:1 down; exit 0; }; }
-
-# get serial number
-
-[ "$DRY" = "yes" ] && SN=00 || \
- SN=$(wget -q -O - http://$IP/versions_en.html | mawk '/MODULE/ { module = 1 } /Serial Number/ { if (module) { printf "%02X", $4; exit 0 } }')
-
-[[ "$SN" =~ ^[0-9A-F][0-9A-F]$ ]] || { echo "unknown serial number ($SN)"; exit 1; }
-
-# configure ip
-
-title "configure ip"
-
-configure ModeServ.cmd serv_mode MANUAL
-configure MacServ.cmd serv_mac 00.80.EE.00.$SN.01
-configure IpServ.cmd serv_ip $(getent hosts | awk '/fe306-'$ID'/ {print $1}')
-configure MaskServ.cmd serv_mask 255.255.255.0
-
-for i in $(seq 1 8); do
- configure MacProd$i.cmd prod_mac$i 00.80.EE.00.$SN.0$((i+1))
- configure IpProd$i.cmd prod_ip$i 10.133.26.1$ID$i
-done
-
-configure IpMulticast.cmd multicast_ip 238.0.0.0
-configure RxMulticast.cmd multicast_rx 62002
-configure TxMulticast.cmd multicast_tx 62004
-configure TTL.cmd ttl 10
-
-# configure gps
-
-title "configure gps"
-
-configure GpsRate.cmd gps_rate 19200
-configure GpsChar.cmd gps_char 8
-configure GpsStop.cmd gps_stop 1
-configure GpsParity.cmd gps_parity no
-
-# configure miscellaneous
-
-title "configure miscellaneous"
-configure BoardNum.cmd board_num $ID
-configure RackNum.cmd rack_num 1
-configure Chan1Num.cmd channel1_num $CH1
-configure Chan2Num.cmd channel2_num $CH2
-
-configure FpgaLoc.cmd fpga_loc FLASH
-configure Clk10Mhz.cmd clk_10 $CLOCKREF
-configure PllConfig.cmd pll_cfg pll_cfg_02
-
-# unset local address
-
-title "unset local address"
-cmd="ifconfig eth1:1 down"
-[ "$DRY" = "yes" ] && echo $cmd || { echo -n $cmd" "; eval $cmd && pass OK || { fail KO; exit 1; }; }
-
-# vim:set tabstop=4 shiftwidth=4 softtabstop=4:
Soft'N'Design Software / projects / debian6500.git / blobdiff